Texio LSA-165V1 Electronic Load (165W/33A/0V-150V)

Home > SHOP ALL PRODUCTS > Brands >

Discontinued

Product Code: LSA-165V1

Description

Application Notes

Hoja de datos formato PDF

Suggested Replacement: PEL-3021

Input
Model			LSA-165	LSA-330	LSA-1000
Input power		H	0W to 165W	0W to 330W	0W to 1000W
		M	0W to 16.5W	0W to 33W	0W to 100W
		L	0W to 1.65W	0W to 3.3W	0W to 10W
Input voltage : CR *1			0V to 150V
Input voltage : except CR *2			1V to 150V
Input current: Rear input terminal			0A to 33A	0A to 66A	0A to 200A
Input current: Front input terminal					0A to 66A
Input terminal form		Front	Screw terminal
		Rear	Cupper bus bar
1: Machine operates with 0V input. However in order to let current flow in equivalent to setting resistance, 1V or more should be input. 2: Machine operates with 1V input or less. However the current actually flows in is less than setting current value or calculated value from input voltage and setting value. In CV mode, affected by current., actual voltage should be more than setting value.
Constant current mode(CC)
Model			LSA-165	LSA-330	LSA-1000
Setting range		H	0A to 33A	0A to 66A	0A to 200A
		M	0A to 3.3A	0A to 6.6A	0A to 20A
		L	0mA to 330mA	0mA to 660mA	0mA to 2000mA
Setting resolution		H	1mA	2mA	6mA
		M	0.1mA	0.2mA	0.6mA
		L	10μA	20μA	60μA
Maximum power		H	165W	330W	1000W
		M	16.5W	33W	100W
		L	1.65W	3.3W	10W
Setting accuracy(at 23℃±5℃)			±(0.2% of set+ 0.3% of fs)
Ripple noise(rms) In the rage of 10Hz to 1MHz		H	10mA	15mA	30mA
		M	5mA	5mA	10mA
		L	1mA	1mA	3mA
Stability (long term drift)			±0.1% of fs typ
Temperature factor(for setting value)			100ppm/℃

Constant resistance mode(CR)
Model			LSA-165	LSA-330	LSA-1000
Setting resistance		H	OPEN, 1.81kΩ to 30.3mΩ	OPEN, 909Ω to 15.1mΩ	OPEN, 303Ω to 5.05mΩ
		M	OPEN, 18.1kΩ to 303mΩ	OPEN, 9.09kΩ to 151mΩ	OPEN, 3.03kΩ to 50.5mΩ
		L	OPEN, 181kΩ to 3.03Ω	OPEN, 90.9kΩ to 1.51Ω	OPEN, 30.3kΩ to 505mΩ
Setting resolution		H	0.55mS	1.1mS	3.3mS
		M	55μS	0.11mS	0.33mS
		L	5.5μS	11μS	33μS
Setting accuracy(Current conversion) at 23℃±5℃		H	±(0.5% of set+ 0.2）A	±(0.5% of set+ 0.4）A	±(0.5% of set+ 1.2）A
		M	±(0.5% of set+ 20）mA + Vin/Rin *3	±(0.5% of set+ 40）mA + Vin/Rin *3	±(0.5% of set+ 120）mA + Vin/Rin *3
		L	±(0.5% of set+ 2）mA + Vin/Rin *3	±(0.5% of set+ 4）mA + Vin/Rin *3	±(0.5% of set+ 12）mA + Vin/Rin *3
Ripple noise(rms) In the rage of 10Hz to 1MHz		H	10mA	15mA	30mA
		M	5mA	5mA	10mA
		L	1mA	1mA	3mA
Stability (long term drift)			±0.1% of fs typ
Temperature factor(for setting value)			1000ppm/℃
*3: Vin means input voltage. Rin refers to approx. 1MΩ. If CR x 10 mode is selected, resistance range will be shifted 10 times more. Meanwhile rating current will be 1/10 in its range.
Constant power mode(CP)
Model			LSA-165	LSA-330	LSA-1000
Setting power		H	0W to 165W	0W to 330W	0W to 1000W
		M	0W to 16.5W	0W to 33W	0W to 100W
		L	0W to 1.65W	0W to 3.3W	0W to 10W
Setting resolution		H	10mW	20mW	100mW
		M	1mW	2mW	10mW
		L	0.1mW	0.2mW	1mW
Setting accuracy		H	±（0.4% of set+ 1.6% of fs）
	at 23℃±5℃	M	±（0.4% of set+ 1.6% of fs）+ Vin2/Rin*3
		L
Ripple noise(rms) In the range of 10Hz to 1MHz		H	10mA	15mA	30mA
		M	5mA	5mA	10mA
		L	1mA	1mA	3mA
Stability (long term drift)			±0.2% of fs typ
Temperature factor(for setting value)			1000ppm/℃
*3: Vin means input voltage. Rin refers to approx. 1MΩ
Constant voltage(CV+CC/CV+CR) mode
Model			LSA-165	LSA-330	LSA-1000
Setting voltage		H	0.1V to 150V
		L	0.1V to 15V
Setting resolution		H	10mV
		L	1mV
Minimum current for operating			1% of fs current
Setting accuracy(at 23℃±5℃)			±(0.2% of set+ 0.1% of fs）
Stability (long term drift)			±0.2% of fs typ
Input current fluctuation			10mV
Temperature factor（for setting value）			1000ppm/℃
Maximum power will be affected by setting current range. Only rating current of setting current range will be loaded when voltage is set to 1V or more. Input current fluctuation: fluctuation for current at input voltage is 1V and 10% to 100% of rating value (when remote sensing is operating) Each Setting range and other setting for CV+CC and CV+CR is equivalent to the CC mode and CR x 1 mode. Noted that CV+CR x 10 mode is NOT available. LSA series has 3 current ranges. So that 6 type of range will be available for each CV+CC and CV+CR.
General specifications
Model			LSA-165	LSA-330	LSA-1000
Temperature			0℃ to 40℃
Humidity			20% to 85%RH(no dew condition)
Storing temperature			-20℃ to 60℃
Storing humidity			20% to 85%RH(no dew condition)
Power requirment			AC100V to AC240V
Power frequency			50Hz / 60Hz
Power consumption			70VA	75VA	130VA
Dielectric strength voltage	primary/chassis		AC1500V 1 min.
	primary/secondary		AC2300V 1 min.
Insulation resistance	primary/chassis		DC500V 10MΩ or more
	primary/secondary		DC500V 10MΩ or more
Cooling			Front fun, rear exhausting forced air cooling
Dimmension(mm)	H×W×D		124×140×383	124×140×383	124×421.5×383
	(Maximum)		148.4×141.8×446.1	148.4×141.8×446.1	140.8×423.3×449
Weight			approx.4.6kg	approx.5.5kg	approx.12.3kg

Features
LSA series is an electronic load which has full-color 3.5 inch LCD display. It provides high operability and visibility. 3 types are available – LSA-165: Input power is 165W (150V/33A), LSA-330: Input power is 330W (150V/66A), LSA-1000: Input power is 1000W (150V/200A). External control interface is standard equipped. GP-IB, USB and RS-232C option control board IF-80GUR provides extended digital interface. Maximum 5-unit-parallel master-slave operation is available.

●　Compact size which is 1/3-rack-size for 165W model and 330W model. Reduce the bulk ratio to 60% of that of the conventional company products.
●　Full-color 3.5 inch LCD provides high operability and visibility.
●　10μA minimum resolution for current setting (LSA-165 L range).
●　Constant Current(CC), Constant Resistance(CR), Constant Power(CP), Constant voltage(CC+CV/CR+CV) mode are selectable.
●　High-speed response for 10μsec. Switching function is available (CC, CR, CP mode).
●　Setting voltage and resistance can be controlled via externally.
●　Maximum 5-unit-parallel master-slave operation is available.
●　Sequence control provides branch on condition.
●　Option: GP-IB, USB and RS-232C are in one slot-in option board IF-80GUR.
* Recommend to use GP-IB or RS-232C if you use LSA seriese at noisy condition

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

SHOP ALL PRODUCTS > Brands
SHOP ALL PRODUCTS > Brands > Texio
SHOP ALL PRODUCTS